Accoya or Thermory: which suits soffits and cladding in Dubai?

Architects who want real timber outside in the Gulf usually end up choosing between two modified woods: Accoya and Thermory. Both are far more stable and durable than ordinary softwood, and both are used on soffits, cladding and screens across the region. They are made in different ways, though, and that changes how they look, how they age and where each one makes the most sense.
How each one is made
Accoya is radiata pine that has been acetylated. The wood is treated with acetic anhydride, which changes its cell structure so it takes up far less water. The manufacturer states that swelling and shrinkage are reduced by 75% or more, and the product carries Class 1 durability.
Thermory is timber, often ash or pine, that has been thermally modified. It is heated to around 215 °C in a controlled kiln without chemicals. This darkens the wood right through and makes it much less attractive to fungi. Thermory's data sheet for its ash product gives durability class 1 under EN 113.
Side-by-side comparison
| Accoya | Thermory (ash) | |
|---|---|---|
| Base timber | Radiata pine, FSC or PEFC certified sources | Mainly European ash or pine |
| Modification | Acetylation | Heat treatment, no chemicals |
| Natural colour | Pale cream, close to untreated pine | Rich brown through the full thickness |
| Durability | Class 1 | Class 1 (EN 113) |
| Stability | Very high, swelling and shrinkage cut by 75% or more | High, with low movement between humid and dry conditions |
| Strength | Close to the original pine | Somewhat more brittle than untreated ash, so fixing details matter |
| Manufacturer warranty | 50 years above ground (subject to terms) | Check the product and profile with us |
| Weathering | Silvers to grey if left uncoated | Silvers to grey if left uncoated |
Which works better for soffits?
For soffits we usually lean towards Accoya. Soffits are hard to reach once installed, so a board that stays straight and holds its coating for longer saves money and scaffolding over the life of the building. Accoya's stability helps coatings last, and its pale colour takes white or light finishes well, which suits many contemporary Dubai designs.
Thermory makes sense when the design calls for a warm, dark timber tone without a stain. Because the colour runs right through the board, small knocks during installation are less obvious.
Which works better for cladding?
Both perform well as cladding. The choice usually comes down to the look the architect wants:
- If you want a light, Scandinavian look or plan to paint or stain, Accoya is the easier base.
- If you want dark, natural timber with minimal finishing, Thermory gets you there straight from the factory.
On a sunny, west-facing elevation, any uncoated timber will fade towards silver grey within months. If the design depends on keeping the original colour, plan for a UV protective coating and a maintenance cycle from the start.
Finishes and maintenance in the Gulf climate
Strong UV, heat and dust are harder on finishes than humidity is. A few practical points:
- A factory applied coating gives the most consistent result, especially on soffits.
- Recoat intervals depend on the coating system, exposure and colour. Lighter, translucent finishes generally need attention sooner than solid colours.
- If you are happy for the timber to weather naturally, both products can be left uncoated. Expect an uneven silvering at first, which evens out over time.
Fire and approvals
Neither product is automatically approved by Civil Defence. Approval for timber is given project by project, and the consultant or contractor makes the submission using the supplier's fire test reports and datasheets. If the project needs a higher fire classification, a tested fire retardant treatment or coating is usually required. We explain the process in more detail in our guide to Civil Defence approval for timber.
Frequently asked questions
Is Accoya better than Thermory?
Neither is better across the board. Accoya is more stable and paler, which suits soffits and painted or light finishes. Thermory gives a dark, natural tone without stains.
Will Accoya or Thermory turn grey in Dubai?
Yes, both weather to silver grey if left uncoated. A UV protective coating keeps the original colour for longer but needs periodic maintenance.
Can I get samples before specifying?
Yes. We can arrange samples for review. Larger panels for client presentations are made up to order and are charged, so contact us with the profile and finish you need.
What is the lead time for Accoya or Thermory in the UAE?
Both are imported to order. Accoya currently takes 8 to 12 weeks from order, and Thermory typically five to six weeks, depending on volume, profile and finish.
Get advice for your project
Tell us where the timber will be used, the approximate area and the look you are after. We will recommend the right product and profile, and send datasheets and pricing.